Home > I Just > I Just Got A New CPU Fan

I Just Got A New CPU Fan

There are computers where you don't need to move the case nor unplug wires, just the power cord, discharge your static and you are good to go. . This reduces the size of the "valleys and craters" and allows for better contact. Or I've heard there's a switch where it could be the wrong voltage.I did take apart everything before but I can't find this switch on where to change the voltage.... Its telling me my fan speed is running at 4700 RPM (very loud) and my temp is at 39C.

Roberto Tomás that video is more than a year old .. At 35db, this small prototype is about as silent as the Intel core2duo boxed cooler when run at a low speed (1500rpm). Stefan Todorov I think it will be problem for your RAM and the PCBs near the CPU, because this thing literally blows the hot air on them Mengede David Wouldn't the AnonymousDec 10, 2011, 5:06 AM Okay.

Each Heatsink bar thing is securely locked in I even looked at the locks. Did you follow these directions when replacing it?????? I know you can improve things using heat sinks and such, but I have yet to see a really good solution for video cards, which are the loudest part of my

It no longer turns it off and I have to flip the back switch. It took a while to install the CPU fan especially since it's so bulky. dirtyferretDec 8, 2011, 10:28 AM what PSU is it?also, make sure the CPU is properly seated, heastsink is properly seated (and tight) and there are no bent CPU pins. Required fields are marked *Comment Name * Email * Kannon Yamada 277 articles Based in Sacramento, Kannon is a Tech journalist (BA) with a background in international affairs (MA).

Give both the HSF and the CPU a very careful cleaning with 90% alcohol. More resources See also CPU Fan loud after upgrading mobo, rams, and psu. Now computer wont boot. If it was there it should work ok as long as the it's seated correctly.

This and overheating are the only two things i can imagine that would cause the system to shut down so quickly. __________________ Help TSF beat Cancer and other serious Illness. If you’re not certain it will fit, you may want to carefully measure it so that length of the heat-sink/fan’s power connector will reach its corresponding connector on the motherboard. Be sure to measure from the base of the CPU to the top of your case. Something tells me that cool chip is the heat sink maker that bought the license for the fan.

  1. Please help!
  2. If you want to go the extra mile and make the most out of your new cooler, see if you can you can get your hands on some high-quality ceramic or
  3. Reply Esaure June 28, 2013 at 8:48 pm Sometimes you have to seat the cooler down to the motherboard before you seat the motherboard to the case (or remove the motherboard
  4. This is a pain in the butt.
  5. Get the answer plaintutsOct 19, 2014, 12:14 AM Ok..You will probably need to disassemble the whole thing..Something is shorting out the motherboard Then re assemble again.
  6. If this isn’t an option, you take the risk of damaging your board.
  7. And this causes your Fans to ramp the Fan up to high RPM's due to poor cooling.
  8. It could be that my Mobo is fried?
  9. Those spin at 7000rpm and bearing wear only becomes an issue about 7 years in or even later.
  10. However, it's a fraction of the size and should clog up with dust a lot less, due to airflow being low-volume but high surface velocity.

It doesn't have a lock like the stock fan that came with the quad core. Legitimately one of the best Customer Service experiences I've had. It isn't working. I think these rings will allow it to work in any orientation.

The PC component that keeps your CPU cool consists of two separate parts – the heat sink, which is typically a block of metal, designed to maximize airflow and surface area. Where you can control the fan speeds. within the Motherboards, Bios & CPU forums, part of the Tech Support Forum category. Once reported, our moderators will be notified and the post will be reviewed.

Discussion is locked Flag Permalink You are posting a reply to: Replaced CPU fan, now computer won't start. is the cpu fan connected to the motherboard fan port?if you have a seperate video card, does it need an additional power connector? Special Considerations When Choosing a CPU Fan and Heatsink Just as not all CPUs are created equal, not all CPU coolers are rated powerful enough to cool every CPU. Because it's new and new is bad?

Comments The Scythe Mugen II in comparison with a boxed cooler. So I tried the hdmi cable without the graphics card, and still the same thing jsut a click coming from the power supply. TDP is the heat output of your CPU, measured in watts.

My guess is the PS is shutting down.

Related Resources Computer wont turn on after adding new mobo, cpu, heatsink/fan and ram. Of the three hard drives, 2 of them beep when plugged in individually, but I don't think that's significant. No beeps when I power on. Second, measure the available height in your case between the top of the CPU and the panel of the computer’s chassis.

I have an FX-8350 processor, Mobo is Gigabyte 78LMT-USB 3, PSU is a corsair cx750 bronze, GPU is 2gb o/c Twin frozr 770. 5 answers Last reply Nov 10, 2014 Best Many coolers require the installation of a backplate on the other side of your motherboard to stabilize them. Not just when upgrading, but as routine for maintenance.Not sure what brand or model Motherboard you have, but if you go to the manufacturers website, you'll find all you need for So here's what I did.

traderjoel I wonder how it can handle dust.